Ships across Europe & the UK Custom requests answered within 2 working hours
£ GBP
EN
Tagsfab — Label Manufacturing

Guides · updated 20 November 2026

Label unwind direction and roll specs: getting the rewind right for your machine

The short answer: a roll of labels is described by four things — which edge of the label leaves the roll first, whether the labels face out or in, the core it is wound on and the largest diameter your machine accepts. The first two give the eight standard unwind positions. Get one wrong and a perfectly printed roll will not feed an applicator, or your printer will add the date upside down. Give us the winding position, the core and the maximum diameter you want in your order or your request — a photograph of the roll that runs on your machine today helps — and we confirm whether we can produce it.

Six finished rolls of shampoo labels of a cosmetic range on a workshop bench, each wound on a cardboard core, with stacks of loose labels in front

In 30 seconds

The 30-second answer: four facts describe a roll

Every label roll that goes into a machine is specified by the same short list:

  • Unwind position, 1 to 8: which edge of the design comes off first — top, bottom, right or left — combined with the winding.
  • Winding: outside wound, labels facing out, is the most common; inside wound, labels facing the core, is what some printers and applicators need.
  • Core: the inner diameter of the cardboard tube — usually 40 or 76 mm; desktop printers often take 25 mm.
  • Outer diameter: the largest roll the machine holds, which sets the number of labels per roll.
  • One label across the web for applicators and most printers; the gap between labels is what the sensor reads.
  • Unsure? A photograph of the roll that runs today, labels visible, settles it.

The chart

What are the eight label unwind positions?

The eight positions combine two windings with four leading edges. Positions 1 to 4 are outside wound, 5 to 8 inside wound; in each group the label leaves the roll top first, bottom first, right edge first or left edge first. The chart below shows each position with the web leaving the roll to the right and the labels seen face up.

The eight unwind positions of a label rollTwo rows of four roll diagrams. In each, the web leaves the roll to the right and two labels show the letter F. Top row, outside wound, labels facing out: position 1 top of the label first, letter rotated so its top points away from the roll; position 2 bottom first, letter pointing towards the roll; position 3 right edge first, letter upright; position 4 left edge first, letter upside down. Bottom row, inside wound, labels facing the core: positions 5 to 8 with the same four orientations, the web leaving from the underside of the roll.Outside wound — labels face outInside wound — labels face inFF1 · top firstFF2 · bottom firstFF3 · right edge firstFF4 · left edge firstFF5 · top firstFF6 · bottom firstFF7 · right edge firstFF8 · left edge firstLabels shown face up; the web leaves the roll towards the right. Top row: web from the top of the roll;bottom row: from the underside. Some machine makers number the positions differently: always add the drawing.
The letter F stands for your design: read where its top points as the web leaves the roll, and you have the position.
The eight unwind positions — the numbering most label charts use
PositionWindingEdge of the design that leaves the roll first
1Outside, labels face outTop
2Outside, labels face outBottom
3Outside, labels face outRight edge
4Outside, labels face outLeft edge
5Inside, labels face inTop
6Inside, labels face inBottom
7Inside, labels face inRight edge
8Inside, labels face inLeft edge

Which edge leads depends on how the label meets the product. On a wrap-around labeller for bottles and jars, with the text running around the container, a side edge goes on first — positions 3, 4, 7 or 8 — and the side depends on the direction the line runs. When the text runs along the direction of travel, the top or the bottom leads. The machine’s documentation states which one it needs; for the label sizes that suit each container, see our bottle and jar label sizes.

Winding

Outside wound or inside wound: what is the difference?

On an outside-wound roll the printed face of the labels is on the outside — you see the design when you look at the roll. On an inside-wound roll the labels face the core and you see only the back of the liner. Outside wound is the most common; some printers and applicators are set up for inside-wound rolls.

Roll of white labels numbered 000001 to 000005 with a data matrix code, unrolled towards the camera on a desk, the numbers reading upright towards the roll
Outside wound, the numbers reading towards the roll: the bottom of each label comes off first — position 2 in the chart.

Reading a roll you already use

  • Labels visible on the outside of the roll: outside wound, positions 1 to 4.
  • Only liner visible: inside wound, positions 5 to 8.
  • Pull out 20 cm of web as the machine does and look at the design: the edge nearest the free end is the one that leaves first.
  • Photograph the roll on the machine, threaded, with the web visible — it is the most reliable specification there is.

Rewinding a roll by hand reverses the order: the last label becomes the first, so position 1 turns into 2 and 3 into 4. It costs time and tension on the web; better to order the right position.

Core and diameter

Which core size and outer diameter?

The core is set by the machine’s spindle, the outer diameter by the space the roll has in the machine. Industrial printers and automatic applicators are built around a 76 mm core and large rolls; desktop printers take smaller cores — 25 mm on many models, 38 to 76 mm with an adaptor — and a roll of about 127 mm outer diameter.

Usual cores by type of machine — the manual of your machine prevails
MachineUsual coreOuter diameter
Desktop label printer25 mm on many models; 38 to 76 mm with an adaptorAround 127 mm on many models
Industrial label printer, print and apply76 mmLarger: see the manual
Automatic or semi-automatic applicator76 mmSet by the unwind arm: see the manual

How many labels on a roll?

Give us either the maximum outer diameter or the number of labels per roll, and we work out the other. The rule of thumb is simple geometry: the area of the ring of labels, divided by the thickness of label and liner, gives the length of web; divided by the pitch, the number of labels.

How the outer diameter of a roll sets the number of labelsCross-section of a label roll with its core. D is the outer diameter of the roll, d the diameter of the core. The formula next to it: labels per roll approximately equals pi times D squared minus d squared, divided by four times t times p, where t is the thickness of label and liner and p the pitch, label length plus gap. Example: D 300 mm, d 76 mm, t 0.15 mm, p 53 mm gives about 8 300 labels.D — outer diameterdcoreLabels per roll ≈ π × (D² − d²) ÷ (4 × t × p)D outer diameter of the rolld diameter of the coret thickness of label + adhesive + linerp pitch: label length in the direction of travel + gapExample: D 300 mm, d 76 mm, t 0.15 mm,p 50 + 3 = 53 mm → about 8 300 labels
An estimate: the real thickness depends on the material and the liner, and we confirm the count with the proof.
Labels per roll, estimated — 50 mm label in the direction of travel, 3 mm gap, total thickness 0.15 mm
Outer diameterCoreLabels per roll, about
127 mm25 mm1 500
200 mm40 mm3 800
250 mm76 mm5 600
300 mm76 mm8 300

Smaller rolls, or larger ones?

Larger rolls mean fewer changes on a line that runs all day; smaller rolls fit a desktop printer and split an order between several packing benches. Ask for a count per roll that matches your batches: a roll that ends with the batch saves a half-used roll on the shelf.

Roll of white barcode labels on a brown cardboard core, outside wound, with a few labels unrolled on the liner
The cardboard core sets the fit on the spindle; the number of turns sets the outer diameter.

On the line

Why does unwind direction matter for a labelling machine?

Because the machine has no say in how the label arrives. An applicator pulls the web over a peel plate, the liner bends back sharply and the label goes straight onto the product: if the wrong edge leads, the design lands sideways or upside down, and nothing in the machine can turn it. A printer works the same way — it prints where its head is, whatever the label shows.

What goes wrong when the roll does not match the machine
MismatchWhat you see on the line
Wrong leading edgeThe label goes on rotated by 90° or 180° on the product
Wrong windingThe web runs with the labels against the rollers, or the peel plate cannot lift them
Core too small or too largeThe roll does not fit the spindle, or wobbles on it
Outer diameter too largeThe roll does not fit the housing or the unwind arm
Overprint panel on the wrong sideThe date or the lot lands outside the panel, or upside down
Several labels acrossAn applicator built for one label across cannot use the roll

Two cases need extra care. When a printer adds the date or the lot before an applicator puts the label on, the position must suit both — our guide to batch numbers, lot codes and expiry dates covers the coding panel. And when a thermal printer is involved, the stock and the core go together: see direct thermal vs thermal transfer. Tension, peel-plate angle and sensor settings are the machine’s business: its manufacturer gives them.

Your order

How do you specify unwind direction with an order?

Write it in the “Anything we should know” box at checkout, or in a custom request for a larger run: six lines are enough, and we then confirm whether we can produce the roll you describe. Give the position as a number and in words — “position 3, outside wound, right edge first” — because charts differ between machine makers.

A roll specification in six lines
LineExampleWhere to find it
Unwind positionPosition 3 — outside wound, right edge firstThe machine’s manual, or the roll it runs today
Core76 mmThe spindle of the unwinder
Maximum outer diameter, or labels per roll300 mm, or 1 000 labels per rollThe manual; your batch size
Labels acrossOneOne for applicators and most printers
Gap the sensor readsStandard gapThe sensor type in the manual
Machine make and modelSemi-automatic wrap-around labellerThe plate on the machine

Not sure? Send the roll you use

A photograph of a roll that runs well on your machine — threaded, the web and the labels visible — tells us the position, the winding and the core in one look. With it, we check whether we can wind the new roll the same way and confirm it to you.

All our label materials are supplied on rolls, white polypropylene for most bottles and jars, overprintable rolls when your printer adds data, and blank rolls when it prints everything.

Example order — 500 ml bottles, semi-automatic labeller
Material
White polypropylene, permanent adhesive
Format
Up to 100 × 70 mm
Print
Full colour, gloss varnish
Roll requested
Position 3, 76 mm core, max. 300 mm — feasibility to be confirmed by us
1 000 labels
£239, excluding VAT
5 000 labels
£430, excluding VAT
10 000 labels
£685, excluding VAT

Configurator prices read on 10 November 2026; production in 4 to 10 working days after proof approval, delivery free in France and calculated by country elsewhere. Quantities are not capped — we print from a hundred pieces to several million.

Before you order

Six roll specification mistakes — and a checklist

The roll rarely fails because of the print; it fails because one line of its specification was missing. The six we see most often:

  1. A position number with no drawing, read on another maker’s chart.
  2. The position chosen for the printer, when the applicator downstream needs another.
  3. A roll too large for a desktop printer, or too small for a line that runs all day.
  4. A 40 mm core on a 76 mm spindle, or the reverse.
  5. Inside-wound rolls for a machine built for outside-wound ones.
  6. Several labels across the web for an applicator that takes one.
Checklist before you order
  • Unwind position as a number and in words, with the chart or a drawing.
  • Core diameter checked on the spindle.
  • Maximum outer diameter, or labels per roll.
  • Labels across, and the gap the sensor reads.
  • Machine make and model, and a photograph of the current roll if you have one.
  • All of it in the order notes or in the custom request; we confirm whether we can produce it.

The glossary terms — core, wind direction, kiss cut — are in our label glossary. Price your run in the configurator and add the roll specification at checkout.

FAQ

Label rolls and unwind direction — what machine users ask us

What is label unwind direction?

It is the way labels come off the roll: which edge of the design leaves first — top, bottom, right or left — and whether the labels face out or in on the roll. The combination gives eight standard positions, numbered 1 to 8, which your printer or applicator needs to receive the label the right way round.

What do outside wound and inside wound mean?

Outside wound means the printed face of the labels is on the outside of the roll; it is the most common. Inside wound means the labels face the core and only the liner shows. Positions 1 to 4 are outside wound, 5 to 8 inside wound.

Which unwind position does my labelling machine need?

Its manual or its manufacturer gives it, because it depends on the side of the line the machine stands and how the product travels. The quickest check is the roll that runs well on the machine today: send a photograph of it, threaded, with your order or request, and we confirm whether we can wind the new rolls the same way.

What core size should I order?

Industrial printers and automatic applicators usually take a 76 mm core; desktop printers often take 25 mm, or a larger core with an adaptor. Measure the spindle or check the manual, then write the core you want in the order notes or in your request: we confirm whether we can produce it.

How many labels fit on one roll?

It depends on the outer diameter, the core, the thickness of label and liner, and the pitch. As an estimate, a 300 mm roll on a 76 mm core holds about 8 300 labels of 50 mm with a 3 mm gap. Give us the maximum diameter or the count you want, and we confirm it.

Can a roll wound the wrong way still be used?

Sometimes, by rewinding it by hand or on a rewinder: the last label then comes first, so position 1 becomes 2 and 3 becomes 4. It takes time and can disturb the web tension, so it is better to specify the position with the order.

Where do I give the winding with an online order?

In the “Anything we should know” box at checkout: the position as a number and in words, the core, the maximum outer diameter or the labels per roll, and the machine model; we confirm whether we can produce it. For a large run, send a custom request.

This guide describes roll specifications in general terms. The position, core and diameter your machine takes, and its own settings — web path, tension, peel plate, label sensor — are set by its manufacturer: check the manual or ask the manufacturer before ordering a large run.

Still unsure?

Ask the person who makes them

The guide covers the general case — your label lives on a real product. Describe it in two lines and a label specialist (not a bot) answers within 2 working hours.

Answered within 2 working hours

Labels on rolls for your machine

White polypropylene from £164 per 100, excluding VAT. Give us the winding position and core you want: we confirm feasibility.

Price my labels
Get a quote — answered within 2 working hours